Mold remediation referrals for Tampa & nearby townsCall: (813) 437-5101
(813) 437-5101

Mold in Walls & Drywall in Dover, FL

moldremediationtampabay.net

In rural eastern Hillsborough, wall mold comes from roofs, plumbing and the AC rather than from the bay.

Mold in the walls of your Dover house?
Call now to be connected with a local mold remediation company in Dover.
(813) 437-5101

Mold inside walls in Dover nearly always starts with an indoor or rain leak: a dripping supply line, a roof or window that lets water in during summer storms, or an AC drain that overflows. Getting rid of it means fixing that leak, removing the moldy drywall and insulation, and drying the framing. Call the number on this page to be connected with a local mold remediation company in Dover.

Technician cutting an inspection opening in drywall, mold in walls & drywall in Dover, FL

Signs the mold is inside a wall

  • Paint lifting or wrinkling in one patch, often near a bathroom or kitchen
  • A smell that's strongest when you open a closet or cabinet on an outside wall
  • Drywall that dents easily near the floor
  • Stains under window sills after heavy rain
  • Spots that come back within a week of being wiped

What drives wall moisture in Dover

Dover is a small unincorporated community in eastern Hillsborough County along U.S. 92, surrounded by farmland and new subdivisions near Strawberry Crest High School. Being inland, its walls rarely see surge. What they do see is the steady moisture load of a humid subtropical climate. The AC runs for most of the year, and every gallon of condensate it pulls from the air has to drain away; a clogged line or rusted pan can wet the wall beside the air handler for weeks. Summer storms test roof flashing and window seals daily from June on, and a slow drip from a supply line can soak the bottom of a wall without ever reaching the floor.

Renters have a clear option here: Hillsborough County Code Enforcement lists mold, along with A/C and heating, among the housing standards it handles in unincorporated areas, and takes reports through its online form. If you're rebuilding after storm damage, Hillsborough County Development Services issues permits; structural repairs in a flood zone need one, while drywall replacement is treated as cosmetic.

Call now to be connected with a local mold remediation company in Dover.
(813) 437-5101
Moisture meter reading on a baseboard, mold in walls & drywall in Dover, FL

What affects cost

Angi reports Tampa-area mold remediation typically runs $1,347 to $3,778 overall and that many companies charge around $10 to $25 per square foot. For walls specifically, Angi's range is $1,075 to $21,500. Where your job falls depends on:

  • How much of the wall has to be opened to reach dry, clean material
  • Insulation and trim that need replacing
  • Whether cabinets or a vanity must be pulled to reach the growth
  • Containment and air filtration for the work area

What happens when you call

You'll be connected with an independent remediation company that serves eastern Hillsborough County. Describe where the damage is, how long you've seen or smelled it, and what you think the source is. They'll usually schedule a look, take moisture readings and give you a written scope. If you also want an independent mold assessment, Florida's s. 468.8419 means it should come from a different company than the one doing the removal.

Mold in Walls & Drywall questions in Dover

Can an AC leak cause mold inside a wall?
Yes. A clogged condensate line or overflowing drain pan can wet the wall around the air handler for weeks before it shows. EPA advises keeping drip pans clean and drain lines flowing.
I rent and there's mold coming through a wall. What should I do?
Tell your landlord in writing, with photos and dates, so the leak behind it gets repaired. If it isn't fixed, the local code enforcement office handles property maintenance complaints. In Dover, Hillsborough County Code Enforcement lists mold among the housing standards it handles.
Will bleach kill mold on drywall?
Not reliably. Drywall paper and gypsum are porous, and EPA notes that porous materials that are moldy may have to be thrown away. Cutting out the affected piece and drying the framing matters more than which cleaner is used.
How do I keep mold from growing back inside the wall?
Fix the water source, make sure the cavity is dry before it is closed, and keep indoor humidity below 60 percent, ideally 30 to 50 percent, as EPA recommends. A working AC with a clear drain line does most of that in a Florida house.

More mold services in Dover

Mold in Walls & Drywall nearby

Call now to be connected with a local mold remediation company in Dover.
(813) 437-5101

Last updated:

☎ Call (813) 437-5101